minimum wall thickness
英 [ˈmɪnɪməm wɔːl ˈθɪknəs]
美 [ˈmɪnɪməm wɔːl ˈθɪknəs]
网络 最小壁面尺寸
双语例句
- The minimum reference value of the wall thickness of GF/ PP products with different content of GF was obtained.
得出了不同含量玻纤增强PP挤出吹塑制件的最小壁厚的参考值。 - The blades are streamlined in shape with a minimum wall thickness of0.
叶片为流线型，按坐标定位，最小壁厚尺寸为0。 - Dimensions, thread gaging, minimum wall thickness and burst pressure, material classification, various quality aspects and requirements for marking identification are stipulated.
尺寸，螺纹规，最小壁厚和爆裂压力，材料分类，各种质量要求和所规定的标记和标识要求等。 - Minimum wall thickness and allowable stress conforms to ANSI B16.34.
最小壁厚和安全应力符合美国国家标准化组织ANSIB16.34标准。 - Minimum wall thickness calculation and analysis of Deepwater Steel Catenary Riser Based on the principles of working stress
基于工作应力准则的深水钢悬链立管最小壁厚计算分析 - A few opinions were suggested to control the appearance quality of the corner joint according to the opinion that the effective thickness of the corner joint should be not less than the minimum wall thickness.
从而根据角接接头有效厚度不应小于最小壁厚的观点，提出对此类角接接头焊缝外观质量控制的几点意见。 - In order to calculate the pipeline's allowed minimum residual wall thickness, the text takes it as the research object, utilizes the finite element software of ANSYS, sets up finite element models, carry on non-linear finite element analysis, thus received its concrete number value.
本文以在役腐蚀缺陷管道的最小允许剩余壁厚为研究对象，利用ANSYS有限元分析软件，建立有限元模型，进行非线性有限元分析，从而得到其具体数值。 - Minimum Wall Thickness Calculation Method for Offshore Deep Water Riser
海洋深水立管最小壁厚计算方法 - It is thought through actual case analysis that elastic unstability of crossing section is unlikely to occur in crossing steel pipelines when conformable with minimum wall thickness limit as per specification requirement.
通过实例分析，认为穿越钢管道在满足规范要求最小壁厚限制时，通常不会发生横截面的弹性失稳，即刚度控制的实质为强度控制。 - This paper finished the following tasks with numerical methods from the aspects of aluminum honeycomb seals structure and sealing performance. ( 1) The minimum wall. thickness of aluminum honeycomb seals was determined by using ANSYS software according to machine design handbook.
本文利用数值方法，针对铝蜂窝密封结构设计及封严特性研究开展了如下主要工作：（1）根据机械设计手册，运用ANSYS软件设计了铝蜂窝密封的最小壁厚。 - According to the different stress analysis and strength conditions, in accordance with the method of stress classification, analyze the elastic and stability of the anchoring section and sliding segment of the pipe, derivate the minimum wall thickness of the pipe under normal operating conditions.
根据不同的受力分析和强度条件，按照应力分类方法，对管道的锚固段和滑动段进行弹性分析和安定性分析，推导正常运行条件下管道的最小壁厚。